Daikin REMQ12P Manual de instalación descargar pdf (Pagina 30)

Installation manual

REMQ8P9 + REMQ10~16P8 + REMHQ12P8Y1B

VRVIII System air conditioner

4PW48463-1A

Setting the mode

The set mode can be changed with the button according

to the following procedure:

■ For setting mode 1: Press the button once, the

H1P LED is off x. This mode is not available for heat recovery

units.

■ For setting mode 2: Press the button for

5 seconds, the H1P LED is on w.

If the H1P LED is blinking c and the button is pushed

once, the setting mode will change to setting mode 1.

Setting mode 2

The H1P LED is on.

Setting procedure

1 Push the button according to the required function

(A~H). The LED indication that matches the required function is

shown below in the ﬁeld marked :

2 When the button is pushed, the current setting is

deﬁned.

3 Push the button according to the required setting

possibility as shown below in the ﬁeld marked .

3.1 Possible settings for function A, B, F, and G are (ON) or

(OFF).

3.2 Possible settings for function C

The noise of level 3 < level 2 < level 1 ( ).

3.3 Possible settings for function D and E

For function D

() only: the noise of level 3 < level 2

< level 1 ( ).

For function E () only: the power consumption of

level 1< level 2 < level 3 ( ).

3.4 Possible settings for function H

The evaporating temperature level H (high) < level M (medium)

< level L (low) ( ).

4 Push the button and the setting is deﬁned.

5 When the button is pushed again, the operation

starts according to the setting.

Refer to the service manual for more details and for other settings.

Conﬁrmation of the set mode

The following items can be conﬁrmed by setting mode 1 (H1P

LED is off)

Check the LED indication in the ﬁeld marked .

1 Indication of the present operation state

- x, normal

- w, abnormal

- c, under preparation or under test operation

2 Indication of low noise operation state

x standard operation (= factory setting)

w operation

3 Indication of power consumption limitation setting

- x standard operation (= factory setting)

w operation

NOTE

If you get confused in the middle of the setting

process, push the button. Then it returns to

setting mode 1 (H1P LED is off).

Possible functions

A additional refrigerant charging operation.

B refrigerant recovery operation/vacuuming operation.

C automatic low noise operation setting at nighttime.

D low noise operation level setting ( ) via the external

control adapter.

E power consumption limitation setting ( ) via the external

control adapter.

F enabling function of the low noise operation level setting

() and/or power consumption limitation setting

() via the external control adapter (DTA104A61/62).

G high static pressure setting

H evaporating temperature setting

H1P H2P H3P H4P H5P H6P H7P

w x w x w x x

w x w x w x w

w x w x w w x

w x w w x x w

w x w w w w x

w x x w w x x

w x w x x w x

w x x w x x x

H1P H2P H3P H4P H5P H6P H7P

w xxxxc x

(a)

(a) This setting = factory setting

w xxxxx c

BS1 MODE

BS2 SET

L.N.O.P

DEMAND

L.N.O.P

DEMAND

BS3 RETURN

BS2 SET

OFF

H1P H2P H3P H4P H5P H6P H7P

(a)

(a) This setting = factory setting

w xxxxx x

w xxxx

x c

w xxxx

c x

w xxxx

c c

H1P H2P H3P H4P H5P H6P H7P

w xxxx x c

(a)

(a) This setting = factory setting

w xxxx c x

w xxx

c x x

H1P H2P H3P H4P H5P H6P H7P

wx x x x x c

(a)

(a) This setting = factory setting

wx x x x c x

c x x x x

H1P H2P H3P H4P H5P H6P H7P

x xwxxxx

H1P H2P H3P H4P H5P H6P H7P

x xwx x xx

H1P H2P H3P H4P H5P H6P H7P

xxwxxxx

OFF

L.N.O.P

DEMAND

BS3 RETURN

L.N.O.P

DEMAND

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 36

Comentarios a estos manuales

Sin comentarios

Daikin REMQ12P Manual de instalación Pagina 30

Comentarios a estos manuales

Relacionado con productos y manuales para Acondicionadores de aire del sistema de división Daikin REMQ12P