Daikin BRC1E72 Guia de preparacion descargar pdf (Pagina 16)

Page 16 of 36 / OM 1169-1

Mode No.

(Note 1)

First Code

No.

Description

Second Code No. (Note 2) (Tinted cells are factory default settings)

01 02 03 04

KRP1B71 X1-X2

status output

Unit Thermistor On/Off

status.

–

Indoor unit operation

On/Off status

Unit Alarm status

1 Unit T1-T2 input

Forced Off

Closed Contact – Unit

is forced off and Central

Control icon is displayed.

Unit cannot be turned on

manually. Operation can

be overridden by central

control.

On/Off

Closed Contact–Unit is

turned off.

Unit responds to last com-

mand, i.e., unit can be

turned on manually or by

central control after circuit

has opened. Operation is

prohibited when remote

controller On/Off control is

restricted by a multi zone

controller.

External Protection

Device

Closed contact–unit

shall resume normal

operation.

Open contact–unit

shall shut down and

generate an A0 error.

Thermo-On/Off dead band

(Note 4).

2F (1C) 1F (0.5C) – –

Fan Speed in Heating Thermo-

Off

LL User set Off –

Fan Speed in Cooling Thermo-

Off

LL User set Off –

Notes: 1.NativeremotecontrollerScheduleandAuto-changeoverfunctionsaredisabledwhenamultizonecontrollerisdetected

and a group address is assigned.

2. Field settings are normally applied to the entire remote control group, however if individual units in the remote control group require

 specicsettingsorforconrmationthatsettingshavebeenestablished,utilizethemodenumberinparenthesis.

3. Any features not supported by the installed unit will not be displayed.

4.Whenmode10-2-01isselected,onlythereturnairtemperaturevalueisreportedtothemultizonecontroller.

5. The actual default dead band value will depend upon the unit model.

Specic Field Settings Changes

Notes: 1 Refer to page13-14for a step by step procedure

for selecting the Mode Number and the First Code

Number, and changing the Second Code Number.

2. For the remainder of the Field Settings section [or

alternatively] In the next three sections, “Setting The

Fan Mode”, “Enabling Setback Temperature

Control”, and “Activating Filter Change Indicator”

Setting The Fan Mode

Continuous Or Auto On/Off

Factory Default Settings:

22-06-02: In cooling mode, when there is no call for cooling,

the fan runs continuously at the speed selected on the Remote

Controller.

22-03-01: In heating mode, when there is no call for heating,

the fan runs continuously at low speed.

Fan Off When Satised

Step 1.

Hold “Cancel” button for 5 seconds to display “Service

Menu”. Scroll down to “Field Settings”. Select by pressing

Menu/OK.

Setup Guide

Mode & Code Settings (Continued)

Step 2.

Press▲▼ buttons until the mode number reaches 22.

Press ◄► buttons until the space next to 06 is highlighted

(cooling mode)

Press▲▼ buttons until the number reads 03, and press Menu/

OK to select.

Select “Yes” when asked to save the settings, and press Menu/

OK to select.

Step 3.

Press ◄► buttons until the space next to 03 is highlighted

(heating mode)

Press ▲▼ buttons until the number reads 03, and press

Menu/OK to select.

Select “Yes” when asked to save the settings, and press Menu/

OK to select.

Step 4.

Press the “Cancel” button twice, and the basic screen returns.

Mode

First

Code No.

Description

Second Code No.

01 02 03

Fan Speed

in Heating

Thermo-Off

LL User set Off

Fan Speed

in Cooling

Thermo-Off

LL User set Off

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 35 36

Comentarios a estos manuales

Sin comentarios

Daikin BRC1E72 Guia de preparacion Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos Daikin BRC1E72